Professional Custom Paper Packaging Factory Since 2003

English

small electronics box List of Tools for Electronics Hobbyists - Start an Electronics Hobby

by:Mengsheng     2020-03-24
As a hobby, many tools are needed for e-projects.Tools can be expensive, but some may last a lifetime, while others may only be used a few times in a particular project.You don't need to buy all the tools available in the store.
In fact, you only need a good tool that is durable to practice your hobbies.A few packs of electronic parts and some basic items are enough to start any electronic experiment.Other electronic components can be purchased if necessary.
Here is a list of basic tools for all junior electronics enthusiasts and expert electronics enthusiasts.Soldering the electronic components together requires soldering iron.Cheap soldering iron usually does not have a temperature controller, but it is still a great tool for many electronics enthusiasts.
Most soldering irons are used properly and are very durable.It will cost a little more to buy a soldering iron station.It is equipped with a temperature controller, a soldering iron bracket and a cleaning sponge.
There is no bracket, you have to be careful where the hot rod is placed.When your hands are too busy to catch the tools, the soldering iron burns and melts anything on your desk!The sponge needs to be wet with water before use and squeezed and dried.A wet sponge is used to clean the tip of the soldering iron.
The iron head is removable.
If the tip is worn and rusted, there is no need to buy a new soldering iron station.Just exchange a few dollars for a new tip.Put two pieces of metal that need to be connected together.
Touch the two contact joints with the hot end of the soldering iron for a few seconds and heat them.Introduce soldering tin at the joint to contact the soldering iron.Solder will melt and flow into the joint.Take the soldering iron slowly.The solder at the joint will cool in a few seconds, and the two metal sheets will be connected together.
Welding is to connect the metal pieces together.Depending on how much your project needs, the soft solder wire has tubes and rolls of different sizes.Tin wire is made of tin and lead.0.5mm to 1mm wires are usually good for hobby projects.
When the soldering tin is in contact with the hot soldering iron above 80 °c, the soldering tin is easy to melt.A large roll of welding with a heavy bracket can set you back for about $40, but it's a good investment if you're going to do a lot of welding.The smaller rolls are cheaper, but they run out soon.
Side cutters are required to cut wires and electronic components.A long time ago, I carefully peeled off the insulation on the wire with a cutter and scissors.This is a tedious job, and the delicate part of the wire is often cut off or removed by accident.
Fortunately, now in most hardware stores, a wire stripping tool is more affordable and available.It is very useful for quickly removing insulation from wires without damaging them.The tool can be used for insulated wires of different diameters.
The wire stripper also has a side knife on the tool itself.A very useful tool.Set of pliers with nonThe sliding handle is sufficient to add to the tool collection.Most pliers can also be used to cut wires.
A set of precision screwdrivers is essential for small electronics projects.Larger parts require a common size screwdriver, so go and buy some good quality screwdriver.Multimeter is voltmeter, ammeter, etc.all-in-one device!At a certain stage, you will need 10 thousand RMB to solve the problem.
Shoot and test your electronic circuit.
The price of a few meters ranges from $10 to several hundred dollars.The basic multimeter is capable of measuring voltage, current, resistance and other parameters.Most digital multimeters require 9 v batteries to work.
Remember to read the instructions on how to use a multimeter with the correct settings, otherwise the multimeter may be broken due to a setup error!The toolbox places all your electronic tools and items in one place.Small electronic components such as resistors, capacitors, diodes, LEDs should be organized in the storage box and labeled accordingly.All resistors and capacitors look the same, and they can easily be confused if kept together.
Store them in separate compartments and it's easy to find them when you need them.The hardware cabinet with many small drawers is an impressive storage space for small electronic spare parts.In order to cover the parts exposed by the wires and prevent them from touching and short circuit, electrical and PVC tape is necessary.
A few rolls of tape should be used enough.This is a great project for beginners and for testing temporary circuits.The price is quite expensive without soldering iron, but it is very interesting.
Learn about the tools and parts you need to start your e-hobby.To start building a circuit, you have to know how the circuit works and how the components work.There are basic tutorials for beginners online.
Most electronic parts and components can be used for different experiments and reused.Read beginner's article on how to use soldering iron, multimeter and how to connect the circuit.Breadboards help test and build different circuits by inserting components and connecting short circuits without the need to weld parts.
Understand the functions of the circuit you are working on.The table below is just a rough guide to the price of some electronic tools to start your hobby.You may want to pay more for better quality tools or for any price that suits your personal budget.
You can find a variety of electronic tools and components on Amazon.com, ebay
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...